E60: SKifte av skiver/bremseklossar bak

[Tuti]

Heisan,

Noko spesielt eg må hugse på før denne jobben? Reknar med det er rett fram.

Må ein alle tider skifte slitasjevarslaren på bremseklossane ? Og kvar er denne lokalisert?

[Reef89]

Gjør akkurat på samme måte som andre biler, ikke begynn å tull med slitasje varslerene, de resetter du bare i Idriven når du er ferdig med bytte.

[Tuti]

Takkar! Då sløyfar eg installering av ny slitasjevarsler.

Er det denne "oppskrifta" du brukar får å resette service intervallar i iDrive?

Firstly with the ignition switched on, set the odometer trip meter back to zero by pushing it once. Then switch the ignition back off again. (I found this step was critical, otherwise I couldn't get to the "Service" menu).

Now you are ready to go through the reset steps as follows:

1. Switch the ignition on (so that the battery, Oil and Parking brake lights are displayed) and the key is ready to start the engine - but don't actually start the car.

2. Press the odometer reset button for between 5 and 10 seconds until a yellow triangle with an exclamation mark in the centre appears in the top window between the clocks (where the outside temperature / time or date normally appears) - this is the "Service" icon.

3. Release the odometer button briefly and press again straight away which brings up a picture of the Brake Fluid symbol (same as the one that the i-drive shows when you look at the Service menu).

4. If you want to reset the Brake Fluid interval for another 2 years then keep holding the odometer button until the word "RESET?" appears at the bottom of the lower window.

5. Release the button briefly and push it in again and hold for about 5 - 10 seconds until the new date appears in the bottom window. You can then switch the ignition off and the new Brake Fluid date will appear in the service menu on the i-drive screen next time you switch on.

6. If you want to reset the Oil, Microfilter or Brake Pad indicators then you will need to follow the same sequence as steps 1 and 2 above, but when you get to step 3 and the brake Fluid icon appears, just release the button and press again and the next service item will appear.

7. You can continue releasing and pressing the button until the required service item icon appears for the one you want to reset. As soon as it does then hold in the button in until the word "RESET?" appears again as in step 4 above. Once the word "RESET?" has appeared, you need to release the button briefly and hold it in again for about 5 - 10 seconds until it is replaced by the new service interval figure (as per step 5 above).

Trur denne skal fungere........

[Gjest]

hvorfor sløyfe slitasjevarlseren? den går ofte (normalt) i stykker under demontering, så hvorfor ikke ha ny klar? den er enkelt å skifte og det er relativt serlvforklarende når du har begynt å skifte.

[Reef89]

Takkar! Då sløyfar eg installering av ny slitasjevarsler.

Er det denne "oppskrifta" du brukar får å resette service intervallar i iDrive?

Firstly with the ignition switched on, set the odometer trip meter back to zero by pushing it once. Then switch the ignition back off again. (I found this step was critical, otherwise I couldn't get to the "Service" menu).

Now you are ready to go through the reset steps as follows:

1. Switch the ignition on (so that the battery, Oil and Parking brake lights are displayed) and the key is ready to start the engine - but don't actually start the car.

2. Press the odometer reset button for between 5 and 10 seconds until a yellow triangle with an exclamation mark in the centre appears in the top window between the clocks (where the outside temperature / time or date normally appears) - this is the "Service" icon.

3. Release the odometer button briefly and press again straight away which brings up a picture of the Brake Fluid symbol (same as the one that the i-drive shows when you look at the Service menu).

4. If you want to reset the Brake Fluid interval for another 2 years then keep holding the odometer button until the word "RESET?" appears at the bottom of the lower window.

5. Release the button briefly and push it in again and hold for about 5 - 10 seconds until the new date appears in the bottom window. You can then switch the ignition off and the new Brake Fluid date will appear in the service menu on the i-drive screen next time you switch on.

6. If you want to reset the Oil, Microfilter or Brake Pad indicators then you will need to follow the same sequence as steps 1 and 2 above, but when you get to step 3 and the brake Fluid icon appears, just release the button and press again and the next service item will appear.

7. You can continue releasing and pressing the button until the required service item icon appears for the one you want to reset. As soon as it does then hold in the button in until the word "RESET?" appears again as in step 4 above. Once the word "RESET?" has appeared, you need to release the button briefly and hold it in again for about 5 - 10 seconds until it is replaced by the new service interval figure (as per step 5 above).

Trur denne skal fungere........

tror denne ere litt enklere:)

1. Skru på tenningen.

2. Hold inne trip teller reset i minst 10 sec.

3. kommer en varsel trekant først så trykk fort på knappen til de ønskede ikonet vises, så hold inne knappen til det kommer reset? yes.